SOLUTION

    UN1000DP

    DP Series Two-platen Injection Molding Machine

    The UN1000DP two-platen injection molding machine which is equipped with the high-performance SmartClamp system, aircraft level aluminum mold technology, alternative temperature technology and FLEXflow servo-driven valve-gated hot runner system is able to perform FoamPro microcellular foam injection molding process developed based on MuCell technology.

     Efficient: dry cycle time up to 4.1 sec, production efficiency up by 22%

     Precise: part weight repeatability <3‰, platen parallelism control accuracy up to ±0.015mm/2ms

     Energy-saving: energy consumption reduced by 56%

    Application example: foamed briefcase

    Ceramic coating technology and ATT eliminate blushing on the foamed part surface.

    Material:LYB PPC foaming grades,FX240/D(PPTalc18)

    Number of cavity:1

    Size:570 (L) ×400 (w) ×40 (H) mm

    Weight:880g

    Cycle time:49s

    Partner:TREXEL、GK Concept、WEIMAT-Pesch、HRSflow、single、lyondellbasell


    UN1200D1

    D1 Series Two-platen Injection Molding Machine

    The advanced cost-efficient Ecoservo SmartPump is 30% more energy-saving than the previous combination of servo motor and fixed-displacement pump

    Quick response and high control accuracy: response speed up by 15%, hold pressure repeatability≤0.2% and flow repeatability≤0.2%

    Noise reduced by 8-10dB

    Compact structure, saving space of factory and reducing maintenance costs

    Designed with piston type suck-back injection cylinder and 25MPa hydraulic pressure to reduce pressure and flow loss



    Application example: console cup holder part

    Ceramic coating technology and ATT eliminate blushing on the foamed part surface.

    Material:ABS+TPV

    Weight:523g

    Cycle time:45s

    Partner

    ASM、WELLLIH、SHINI、magbo

    UN1500DP

    DP Series Two-platen Injection Molding Machine

    Electric plasticizing system with high torque and high reduction ratio, suitable for synchronized plasticization on large injection molding machines and substantially improving production efficiency

    Compact structure, driven by four symmetrically-located small-power motors with sync output power and high efficiency

    Low energy consumption, uniform force distribution on the gear, good cooling effect and long lifespan

    Multiple small-power motor modules that can be replaced separately, no influence of abroken-down motor on the normal ones

    Noise reduced by 8-10dB



    Application example: high-gloss car spoiler

    Using servo-driven valve-gated hot runner system to eliminate weld lines

    Material:Finalloy®EBP-830 PP/EPDM+T20

    Weight:1360g

    Cycle time:68s

    Partner:WELLLIH、FORWELL、SHINI、single

    FE60-130h

    FE Series All-electric Injection Molding Machine

    Used for molding of precision automotive parts, with accuracy up to ± 0.01mm

    Stable part production with 100% QC pass rate

    Cycle time of 20 seconds, resulting in production efficiency 1 time higher than that of the traditional solution

    High energy efficiency, average hourly power consumption as low as 1 kWh

    The use of fully-automated flow production solution and SCARA robot maximizes the speed of production and packing



    Application example: automotive trunk gear


    Material:POM F20-30 A7A5023T

    Weight:0.38g

    Number of cavity:4

    Cycle time:20s

    Dimensional accuracy:±0.01mm

    Weight variance:±0.01g

    End-use market:auto part

    Partner:SHINI

    FE120-130h

    FE Series All-electric Injection Molding Machine

    Used for injection molding of medical devices  

    Pinhole size of 0.39mm±0.01mm, precision up to standard        

    Good light transmission, no yellow marks or bubbles, stable performance

    High repeatability, zero rejection rate        

    Automatic sorting available, real-time warning of process parameter change, reduction of manual inspection

    Automated operation accelerates production and packing and ensures cleanliness and hygiene of the parts        



    Application example: medical device


    Material:PC        

    Weight:1.45g        

    Number of cavity:2        

    Cycle time:21s        

    Dimensional accuracy:±0.01mm        

    Weight variance:±0.01g        

    End-use market:medical        

    Automation partner:SHINI        

    FE260-640h

    FE Series All-electric Injection Molding Machine

    Used for thin-walled food packaging applications        

    1mm-thick molded parts, stable injection molding process without short shot or flash        

    Real-time monitoring of the plastics parts with use of sorting function to ensure 100% QC pass rate  

    Additional conveyor to make part collecting and packing faster and easier              



    Application example: spoon


    Material:PP        

    Weight:2.5g        

    Number of cavity:16        

    Wall thickness:1mm        

    Cycle time:±0.01mm                

    End-use market:food packaging        

    Automation partner:SHINI        

    UN120SJ II

    SJ Series Injection Molding Machine for High-end Precision Parts

    Mobile phone accessory molding: high speed, large force, stable performance, thin-walled parts including 0.5-0.8mm thick mobile phone cases and plastic mobile phone frames        

    High injection speed: 40% higher than that of a general injection molding machine. High-speed mold filling, resulting in lower internal stress in the molded parts and less deformation      

    Accurate temperature control: temperature control tolerance in the static test is ±0.5, delivering convenient process adjustment and stability control

    Optical parts: no shrinkage, no light diffusion, no gas marks, low rejection rate            



    Application example: mobile phone frame


    Material:PC 2501              

    Number of cavity:2        

    Size:130mm×70mm        

    Weight:0.17g                

    Cycle time:15s        

    Partner:TOPSTAR        

    UN260A5

    A5 Series Standard High-end Servo Injection Molding Machine

    Good plasticizing effect: no occurrence of molding defects, such as black spots, white spots, yellow marks, silver streaks and bubbles during long-term use of the machine

    Low energy consumption: hourly energy consumption as low as 4.3KWh

    High stability: under standard molding conditions, position control accuracy up to±0.2mm and part weight repeatability≤1‰                    



    Application example: cosmetic jar


    Material:PETG              

    Number of cavity:4              

    Weight:139g*4                

    Cycle time:120s        

    Weight variance:≤1‰                

    Injection speed:46mm/s      

    Wall thickness:15mm        

    Partner:TOPSTAR        

    UN320SM

    SM Series Servo Injection Molding Machine

    Energy-saving: classic energy-saving servo system, small rotating inertia, no bottom current and lower energy consumption

    Stable: mold-open and mold-close position repeatability up to ±2mm, injection position repeatability up to ±0.1mm, part weight repeatability≤5‰

    Fast plasticizing, short cycle time, high overall machine efficiency                    



    Application example: humidifier base


    Material:ABS              

    Number of cavity:1                

    Size:200mm×165mm                

    Weight:268g              

    Cycle time:45s              

    Partner:TOPSTAR        

    PAC450K

    High-speed 4+4 Cavity Injection Molding System for Thin-walled Container

    Upgraded configuration and greatly enhanced performance

    Injection speed up to 400-500mm/s

    Optimized platen design and Yizumi 4+4 stack molds



    Application example: 1000ml disposal container

    Using servo-driven valve-gated hot runner system to eliminate weld lines

    Material:PP980

    Number of cavity:4+4 stack mold

    Weight:16.5g×8

    Cycle time:5.5s

    Partner:SHINI

    PAC200

    High-speed IML System for Thin-walled Container

    ● Shorter cycle time and higher efficiency

    ● High accuracy of part weight and dimensions

    ● Lower production costs



    Application example: small IML cup

    Material:PP980

    Weight:7g×4

    Cycle time:3.5s

    Partner:SHINI

    PET48-ECO

    High-speed Preform Injection Molding System

    ● High production volume: higher injection speed and shorter cycle time

    ● Large shot weight: single-station plasticization ensures sufficient shot weight, with maximum plasticizing volume up to 3,300 g

    ● High rigidity: unique linear guide rails and non-contact tie bars that reduce the resistance to the movable platen and prolong the mold life

    ● High responses: high-end control system with program scanning time of only 1ms, effectively shortening the response time



    Application example: preform

    Material:PET

    Number of cavity:48

    Weight:15g

    Cycle time:9.5s

    Partner:GoldenBox

    YL2-V280L

    European Standard RIM

    ● Patented“three-balanced vertical injection cylinder”structure, precise control of injection stroke, "FILO" injection system.      

    ● High speed Siemens PLC, Version 4 proprietary software, free-editable machine sequence, communication access available for MES.

    ● Energy efficient dynamic system with low heating consumption design.                  

    ● Machine operation per European habits, and with easy mold compatibility.                    

    ● Energy efficient precise hydraulic system.                    

    ● CE compliance.                    

    ● Wireless remote control.                    

    YL2-V630L

    European Standard RIM

    ● Patented“three-balanced vertical injection cylinder” structure, precise control of injection volume, "FILO"injection system.        

    ● Three-step closing mechanism, low-bed design, energy-efficient clamping structure, heating plate design suitable for European customers.            

    ● High speed Siemens PLC, Version 4 proprietary software, free-editable machine sequence, communication access available for MES.                      

    ● PC panel.                    

    ● Wireless remote control.                  

    ● CE compliance.                      

    ● Modular design, with diversified combinations can easily satisfy customers’individualized requirements.                      

    YL2-VV350L

    Vertical Vacuum Chamber Injection Molding Machine

    ● Patented“ three-balanced vertical injection cylinder” structure, precise control of injection volume,"FILO" injection system.        

    ● Durable vacuum chamber structure, particularly suitable for molding sophisticated parts.                      

    ● Fast response Siemens PLC, Version 4 proprietary software, free-editable machine sequence, communication access available for MES.                  

    ● Servo motor system, precise control, energy efficient.                    

    ● Oil tempering unit with extended service life and low carbon deposition (over-temperature protection).                  

    ● Quick mold changeover.                    

    ● Auto strip feeding device.                  

    ● Auto strip feeding device (including pneumatic door).                

    ● KCS safety standard.                    

    YL-H350F

    Horizontal RIM Series

    ● “FIFO” injection system, injection piston fully retractable, precise control of injection volume                

    ● Horizontal clamping structure, ideal for automatic molding        

    ● High efficiency & low energy consumption design        

    ● Advanced B&R control system        

    ● Free access for MES        

    ● Automatic single brush system      

    YL2-V250L

    Asian Standard RIM

    ● Patented“ three-balanced vertical injection cylinder” structure," FILO" injection system; precise control of injection volume.        

    ● High speed Siemens PLC, Version 4 proprietary software, free-editable machine sequence, communication access available for MES.        

    ● Oil tank at rear side, less floor space required, front side can be configured with multiple layer ejecting device.        

    ● Energy efficient dynamic system with lower heating consumption design.    

    ● Oil tempering unit with extended service life and low carbon deposition.        

    ● The dedicated 4RT structure with big stroke and with movement free-editable.        

    ● Modular design, diversified combinations can quickly satisfy customers’ individual demands.        

    YL2-V300L

    Asian Standard RIM

    ● Patented“ three-balanced vertical injection cylinder” structure," FILO" injection system; precise control of injection volume.        

    ● High speed Siemens PLC, Version 4 proprietary software, free-editable machine sequence, communication access available for MES.                      

    ● 700×750mm big heating platen, oil tank on right hand side, high-bed design, multiple layer ejector system can be either installed in the front side or at the rear side.                      

    ● Oil tempering unit with extended service life and low carbon deposition.                      

    ● 3RT structure with big stroke and free-editable sequence.                    

    Modular design, diversified combinations can quickly satisfy customers' individual demands.                      

    HPM Thixomolding Machine UN650MGⅡ

    ● High-speed mold opening and closing technology, excellent performance and high reliability

    ● High-quality and durable barrel assembly with heat-resistance up to 650℃

    ● Real-time control of high-speed injection is available thanks to the closed-● loop control technology based on self-developed control software and algorithm

    ● Maximum injection speed up to 5m/s



     Application example: laptop keyboard base

    Material:AZ91D

    Number of cavity:1

    Size:335×230 ×10mm

    Weight:124g

    Cycle time:36s

    Wall thickness:0.45-0.65mm

    500T die casting cell

    ● Highly automated unmanned production, stable and reliable product quality, high repeatability and low failure rate  

    ● Shorter cycle time and higher production efficiency  

    ● Highly integrated post-processing of semi-finished die cast parts, reducing space and transportation and achieving automation of machine and peripherals

    ● Central control system provides complete data records for the whole die casting process and production process, with real-● time monitoring and display                          

    Guangdong Yizumi Precision Machinery Co., Ltd.    All rights reserved    粤ICP备 No. 13006819

    Privacy Policy Legal Notice Sitemap Contact Us